|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Features * * * * * * * * * * * * * * * * * * 100mA Output from a Single AA Cell Input 250mA Output from a Dual AA Cell Input 400mA Output from a Single Lithium-Ion Cell Input VIN Operation Range: 0.8V to VOUT Up to 93% Efficiency Low Start-Up Voltage: 1.0V Typical Internal Synchronous Rectifier Current Mode Control with Internal Feedback and Compensation 2MHz Fixed Switching Frequency 1A Current Limit Maintains High Efficiency Over the Output Current Range for Improved Battery Life Low 40A No Load Bias Current True Load Disconnect Short-Circuit and Over-Current Protection Inrush Current Limit and Soft Start Low Shutdown Current: <1.0A -40C to +85C Temperature Range 2.0x2.1mm SC70JW-8 Package General Description The AAT1265 is designed for single-cell or dual-cell alkaline, NiMH, or NiCd or single-cell lithium-ion/polymer (Li-Ion) battery-powered applications. It is a high efficiency, synchronous, fixed frequency, step-up converter with true output disconnect during shutdown (<1.0A), start-up inrush current limit, and short-circuit protection. The high 2MHz switching frequency and completely integrated control circuitry minimize the total solution footprint area while maintaining excellent regulation, ripple, and transient response throughout the full load range. Light load switching frequency modulation and low quiescent current maintain high efficiency performance for light load and sleep mode conditions. With a 1A peak switch current limit, the AAT1265 is capable of delivering 100mA to the load with a single AA cell, up to 250mA from a dual AA cell, or up to 400mA from a single-cell lithium-ion battery. The device has a 1.0V start-up voltage with operation down to 0.8V. The AAT1265 is available in a Pb-free, space-saving 2.0x2.1mm 8-pin SC70JW package and is rated over the -40C to +85C temperature range. Applications * * * * * Bluetooth(R) Headsets Digital Cameras Medical Instruments Mobile Handsets MP3 and Portable Music Players Typical Application VIN 2.2H LX AAT1265 VCC Efficiency (%) VOUT 100 Dual-Cell to 3.3V Efficiency vs. Output Current VIN = 3.0V 90 80 VIN OUT 4.7F VIN = 2.4V 70 60 VIN = 2.0V 4.7F EN GND 50 0.1 1.0 10.0 100.0 1000.0 Output Current (mA) 1265.2007.12.1.4 www.analogictech.com 1 PRODUCT DATASHEET AAT1265 SwitchRegTM Pin Descriptions Pin # 1 2 3 4 5 6, 7, 8 Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Symbol VCC EN VIN LX OUT GND Function Bias supply voltage after start-up and feedback to the output voltage error amplifier. Enable pin. Logic high enables the IC. Logic low disables the IC and disconnects the load from the input. Shutdown current is <1A. Battery input voltage. Supplies the IC at start-up. Inductor connection. Ties to the drains of the P-channel synchronous rectifier and the N-channel MOSFET switch. Boost converter output voltage; connects to the P-channel synchronous MOSFET source. Bypass with ceramic capacitor to GND. Signal and power ground. Connect output capacitor return. Pin Configuration SC70JW-8 (Top View) VCC EN VIN LX 1 8 GND GND GND OUT 2 7 3 6 4 5 2 www.analogictech.com 1265.2007.12.1.4 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Absolute Maximum Ratings Symbol VN TJ TLEAD Description VIN, OUT, VCC, EN, LX to GND Operating Junction Temperature Range Maximum Soldering Temperature (at leads, 10 sec) Value -0.3 to 6.0 -40 to 150 300 Units V C C Thermal Characteristics1 Symbol JA PD Description Maximum Thermal Resistance Maximum Power Dissipation Value 160 625 Units C/W mW 1. Mounted on an FR4 board. 1265.2007.12.1.4 www.analogictech.com 3 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Electrical Characteristics1 VIN = 1.2V, TA = -40C to +85C, unless otherwise noted. Typical values are TA = 25C. Symbol VIN VOUT IQ ISHDN RDS(ON)H RDS(ON)L ILIMIT IPFM VOUT/ VOUT VOUT/ VOUT/VIN FOSC DTYMAX VTH(L-IN) VTH(H-IN) Description Minimum Start-Up Voltage Operating Input Voltage Range Output Voltage Accuracy Quiescent Supply Current (Light Load Operation)2 Shutdown Current PMOS On-Resistance NMOS On-Resistance NMOS Current Limit PFM Light Load Current Threshold Efficiency Load Regulation Line Regulation Switching Frequency Maximum Duty Cycle Logic Input Low Threshold for EN Logic Input High Threshold for EN Conditions ILOAD = 1mA VIN = 0.8V to 2.5V, PWM Mode VIN = 2.5V to 4.2V, PWM Mode; 5.0V Version Only No Load EN = 0V, VIN = 5.5V TA = 25C TA = 25C Min 0.8 VOUT - 0.1 VOUT - 0.15 Typ 1.0 Max VOUT VOUT + 0.1 VOUT + 0.15 Units V V V A A m m A mA % % %/V 40 750 400 1.0 20 82 1.5 0.2 0.16 1.8 2.0 90 70 1.0 IOUT = 50mA, L = 2.2H ILOAD = 0 to 100mA VIN = 0.8V to 2.5V VIN = 2.5V to 4.2V; 5.0V Version Only TA = 25C 2.2 0.4 1.0 MHz % V V 1. The AAT1265 is guaranteed to meet performance specifications over the -40C to +85C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 2. IQ = IQ_VOUT + IQ_VCC. 4 www.analogictech.com 1265.2007.12.1.4 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Typical Characteristics Single-Cell to 3.3V Efficiency 100 90 100 Dual-Cell to 3.3V Efficiency VIN = 3.0V Efficiency (%) Efficiency (%) VIN = 1.5V 90 80 80 70 60 50 0.1 VIN = 2.4V 70 60 50 VIN = 2.0V VIN = 1.2V 1 10 100 1000 0.1 1 10 100 1000 Output Current (mA) Output Current (mA) Single-Cell Load Regulation (VOUT = 3.3V) 2.0 1.5 2.0 1.5 Dual-Cell Load Regulation (VOUT = 3.3V) VOUT Error (%) VOUT Error (%) 1.0 0.5 0.0 -0.5 -1.0 -1.5 -2.0 0.1 1 1.0 0.5 0.0 -0.5 -1.0 -1.5 -2.0 VIN = 3.0V VIN = 2.4V VIN = 1.5V VIN = 1.2V 10 100 VIN = 2.0V 0.1 1 10 100 1000 Output Current (mA) Output Current (mA) Li-Ion/Polymer to 5V Efficiency 100 2 Li-Ion/Polymer Load Regulation (VOUT = 5V) VIN = 3.6V VOUT Error (%) 0 VIN = 3.1V Efficiency (%) 80 60 VIN = 4.2V -2 VIN = 3.1V VIN = 3.6V 40 VIN = 4.2V 20 0.1 1 10 100 1000 0.1 1.0 10.0 100.0 1000.0 Output Current (mA) Output Current (mA) 1265.2007.12.1.4 www.analogictech.com 5 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Typical Characteristics 3.3V to 5V Efficiency 100 2 3.3V to 5V Load Regulation Efficiency (%) 80 Output Error (%) 0 60 -2 40 20 0.1 1 10 100 1000 -4 0.1 1 10 100 1000 Output Current (mA) Output Current (mA) Minimum Start-Up Voltage vs. Load Current (VOUT = 3.3V) 2.4 2.2 2.0 Light Load Mode Output Current Threshold vs. Input Voltage 120 Output Current (mA) 100 80 60 40 20 0 Constant Current Load Increasing Load Voltage (V) 1.8 1.6 1.4 1.2 1.0 0.8 0 2 40 60 80 100 120 140 160 Resistive Load Decreasing Load 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 Current (mA) Input Voltage (V) No Load Input Current vs. Input Voltage (VOUT = 3.3V) 200 No Load Input Current vs. Input Voltage (VOUT = 5V) 350 Input Current (A) 160 120 80 40 0 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 Input Current (A) 300 250 200 150 100 50 0 1.8 2.2 2.6 3.0 3.4 3.8 4.2 4.6 Input Voltage (V) Input Voltage (mA) 6 www.analogictech.com 1265.2007.12.1.4 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Typical Characteristics Switching Frequency vs. Temperature Switching Frequency Change (%) 0.5 600 Maximum Load Current Capacity for a 4% Drop in Output Voltage vs. Input Voltage (VOUT = 3.3V) Load Current (mA) 500 400 300 200 100 0 0.0 -0.5 -1.0 -1.5 -2.0 -2.5 -40 -15 10 35 60 85 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 Temperature (C) Input Voltage (V) Maximum Load Current Capability for a 4% Drop in Output Voltage vs. Input Voltage (VOUT = 5V) 800 Load Transient Response (VIN = 1.2V; L = 2.2H; CO = 4.7F) 3.40 Load Current (mA) Output Current (A) 700 600 500 400 300 200 100 1.8 3.35 3.30 3.25 3.20 0.15 0.10 0.05 0.00 50mA 100mA Output Voltage (V) 2.2 2.6 3.0 3.4 3.8 4.2 4.6 Input Voltage (V) Time (50s/div) Output Voltage vs. Temperature (VIN = 1.5V; IOUT = 10mA; VOUT = 3.3V) 0.40 Line Transient Response (IOUT = 50mA; L = 2.2H; COUT = 4.7F) 2.50 2.4V Output Voltage Error (%) 0.20 Output Voltage (V) 2.25 Input Voltage (V) 0.00 -0.20 -0.40 -0.60 -0.80 -40 2.00 1.9V 3.34 3.32 3.30 3.28 3.26 1.75 1.50 -20 0 20 40 60 80 Temperature (C) Time (50s/div) 1265.2007.12.1.4 www.analogictech.com 7 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Typical Characteristics Soft-Start Inrush Current (VIN = 1.2V; IOUT = 40mA; VOUT = 3.3V) Enable and Output Voltage (V) 4 3 2 1 0 -1 -2 -3 -4 1.75 Soft-Start Inrush Current (VIN = 2.4V; IOUT = 100mA; VOUT = 3.3V) Enable and Output Voltage (V) 4 3 2 1 0 -1 -2 -3 -4 1.75 Output Voltage 1.5 Output Voltage 1.5 Input Current (A) Input Current (A) 1.25 1.25 1 Enable 1 0.75 0.5 Enable 0.75 0.5 0.25 Input Current 0.25 0 -0.25 Input Current Time (500s/div) 0 -0.25 Time (500s/div) Full Load Output Ripple (VIN = 1.2V; IOUT = 10mA; VOUT = 3.3V) VOUT (AC Coupled) (20mV/div) IL (100mA/div) VLX (2V/div) VOUT (AC Coupled) (20mV/div) IL (200mA/div) VLX (2V/div) Light Load Output Ripple (VIN = 1.2V; IOUT = 100mA; VOUT = 3.3V) Time (250ns/div) Time (1s/div) 8 www.analogictech.com 1265.2007.12.1.4 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Functional Block Diagram VCC VIN OUT Start-Up Inrush Control VREF Low Voltage Start-Up Voltage Reference Mode Control DH 2MHz Oscillator Logic LX Current Sense Comp. DL Error Amp. GND EN GND Functional Description The AAT1265 synchronous step-up converter is targeted for single- or dual-cell alkaline, NiMH, and NiCd and single-cell lithium-ion/polymer battery applications. It has a 1V typical start-up voltage with operation after start-up to less than 0.8V. The high 2MHz switching frequency of the AAT1265 facilitates output filter component size reduction for improved power density and reduced overall footprint. It also provides greater bandwidth and improved transient response over other lower frequency step-up converters. The compensation and feedback is integrated with only three external components (CIN, COUT, L). Low RDS(ON) synchronous power switches provide high efficiency for heavy load conditions. Switching frequency modulation and low quiescent current maintains this high efficiency for light load and sleep mode conditions. In addition to the improved efficiency, the synchronous boost has the added performance advantage of true load disconnect during shutdown (<1A shutdown current), inrush current limit, and short-circuit protection. PWM / Light Load Control The AAT1265 is a fixed frequency PWM peak current mode control step-up converter. For light load conditions (10 to 20mA and below), the converter transitions to a variable 1265.2007.12.1.4 www.analogictech.com 9 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Applications Information Inductor Selection The AAT1265 is designed to operate with a 2.2H inductor for all input/output voltage combinations. The inductor saturation current rating should be greater than the NMOS current limit specification listed in the Electrical Characteristics table. If necessary, the peak inductor current can exceed the saturation level by a small amount with no significant effect on performance. Table 1 provides a list of some suggested inductor manufacturers and their part numbers. frequency (Light Load) mode to reduce the dominant switching losses. In addition to Light Load operation, a zero current comparator blocks reverse current in the P-channel synchronous MOSFET, forcing DCM operation at light load. These controls, along with very low quiescent current, help to maintain high efficiency over the complete load range without the compromise of increased output voltage ripple during light load conditions. Start-up and Inrush Current Limit The start-up sequence of the AAT1265 varies depending upon whether the input voltage is greater than or less than 2V. Above 1V, a start-up oscillator operating at 25% duty cycle controls the synchronous power stage and charges the output to 2V. For an input voltage greater than 2V, the output is charged at a constant current of 300mA until the output reaches a voltage level just below the input voltage. The step-up converter then takes control and continues to charge the output to the steady-state voltage. The step-up converter N-channel switch current is limited to 1A and the typical start-up time is 2.5ms. Output and Input Capacitor Selection Surface mount X5R or X7R ceramic capacitors are suggested for both the output and the input. For the output capacitor (C1 in Figure 4) a 4.7F, 10V, X5R ceramic capacitor is necessary for stability, transient response, and ripple performance. The same 0805 sized capacitor is used for the input (C2 of Figure 4). If desired, a smaller, 0603 sized, 4.7F, 6.3V, X5R ceramic capacitor can be substituted for the input capacitor (C2). Suggested ceramic capacitor suppliers are listed in Table 1. Shutdown and Output Disconnect A typical synchronous step-up (boost) converter has a conduction path from the input to the output via the body diode of the P-channel MOSFET. The AAT1265 design disconnects this body diode from the output and eliminates this conduction path. This enables the AAT1265 to provide true load disconnect during shutdown and inrush current limit at turn-on. PCB Layout Guidelines Figures 1, 2, and 3 display the evaluation board layout and suggested component placement. Due to the high switching speed of the AAT1265, it is important that the evaluation board layout be followed. Even the best switch-mode power supply design cannot overcome the problems that can be caused by a poor layout. For the AAT1265, it is necessary that C1 and C2 be placed as close as possible to the IC with a good low impedance path to the GND pins of the IC. It is also good practice to minimize the length of the trace from the OUT pin to the output inductor. This prevents switching noise from radiating into other high noise sensitive, high impedance circuits. Short-Circuit Protection The P-channel synchronous MOSFET body diode disconnect feature also gives the AAT1265 the ability to provide output short-circuit current limit protection. 10 www.analogictech.com 1265.2007.12.1.4 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Figure 1: AAT1265 Evaluation Board Top Side. Figure 2: Component Placement. Figure 3: AAT1265 Evaluation Board Bottom Side. 1265.2007.12.1.4 www.analogictech.com 11 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package VIN U1 AAT1265 1 1 2 3 2 3 4 VCC GND EN VIN LX GND GND OUT 8 7 6 Enable L1 2.2H C2 4.7F VOUT 5 C1 4.7F U1 AAT1265 SC70JW-8 L1 SD3118-2R2 C1, C2 4.7F 10V 0805 X5R Figure 4: AAT1265 Evaluation Board Schematic. Manufacturer Murata www.murata.com TDK www.tdk.com Taiyo Yuden www.t-yuden.com Value 4.7F 4.7F 4.7F Part Output or Input Capacitor Input Capacitor Output or Input Capacitor Input Capacitor Output or Input Capacitor Input Capacitor Voltage 10V 6.3V 10V 6.3V 10V 6.3V Case Size 0805 0603 0805 0603 0805 0603 Part Number GRM21BR61A475KA73L GRM188R60J475KE19D C2012X5R1A475K C1608X5ROJ475K LMK212BJ475MG JMK107BJ475MA Manufacturer Sumida www.sumida.com Cooper Electronics www.cooperet.com Value 2.2H 2.2H Part Inductor Inductor ISAT 1.50A 1.62A DCR 75m 69m Case Size 3.2 x 3.2 x 1.55 3.1 x 3.1 x 1.85 Part Number CDRH2D14-2R2 SD3118-2R2 Table 1: Suggested Component Selection. Advanced Analogic Technologies, Inc. 3230 Scott Boulevard, Santa Clara, CA 95054 Phone (408) 737-4600 Fax (408) 737-4611 (c) Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Except as provided in AnalogicTech's terms and conditions of sale, AnalogicTech assumes no liability whatsoever, and AnalogicTech disclaims any express or implied warranty relating to the sale and/or use of AnalogicTech products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders. 12 www.analogictech.com 1265.2007.12.1.4 PRODUCT DATASHEET AAT1265 SwitchRegTM Low Voltage 2MHz Step-Up DC/DC Converter in SC70JW Package Ordering Information Voltage 3.0V 3.3V 3.6V 5.0V Package SC70JW-8 SC70JW-8 SC70JW-8 SC70JW-8 Marking1 TCXYY RLXYY TBXYY UQXYY Part Number (Tape and Reel)2 AAT1265IJS-3.0-T1 AAT1265IJS-3.3-T1 AAT1265IJS-3.6-T1 AAT1265IJS-5.0-T1 All AnalogicTech products are offered in Pb-free packaging. The term "Pb-free" means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/pbfree. Package Information SC70JW-8 0.50 BSC 0.50 BSC 0.50 BSC 1.75 0.10 0.225 0.075 2.00 0.20 2.20 0.20 0.048REF 0.15 0.05 0.85 0.15 1.10 MAX 0.100 7 3 0.45 0.10 2.10 0.30 4 4 All dimensions in millimeters. z 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. Advanced Analogic Technologies, Inc. 3230 Scott Boulevard, Santa Clara, CA 95054 Phone (408) 737-4600 Fax (408) 737-4611 (c) Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Except as provided in AnalogicTech's terms and conditions of sale, AnalogicTech assumes no liability whatsoever, and AnalogicTech disclaims any express or implied warranty relating to the sale and/or use of AnalogicTech products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders. 1265.2007.12.1.4 www.analogictech.com 0.05 0.05 13 |
Price & Availability of AAT126507 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |